Acs tr 069

FAQ How do I buy the products? You can get products in offline stores or online retailers according to the above sheet. Contact sales if you need special firmware or when you want to buy in bulk. How do I prepare to deploy TR-069 in my network? Deploying TR-069 requires compatible CPE devices and ACS. Tech specialists are needed for the maintenance of ACS. If you simply want to boost your deployment, you may look for Aginet Config. How do I enable auto-configuration on TR-069 devices? Set the ACS address, profile info (username and password) for devices in advance to enable auto-configuration. TP-Link recommends using Aginet Config to deploy the ACS settings efficiently. Does TP-Link offer an official ACS solution for TR-069 products? If you are looking for the ACS solution provided by TP-Link, you may check out Aginet ACS offered by a TP-Link Service Provider. The products supported by Aginet ACS differ from those listed on this page.

Step 12 cwmp agent Example:Device(config)# cwmp agent Enables TR-069 Agent configuration mode. Step 13 enable download Example:Device(config-cwmp)# enable download (Optional) Enables the CPE to permit a software download. By default, this command is disabled. Step 14 session retry limit session-count Example:Device(config-cwmp)# session retry limit 10 (Optional) Sets the session retry count whenever the TR-069 session establishment fails with the ACS. The range for the session count argument is 0 to 15. The default value is 11. Step 15 request outstanding request-count Example:Device(config-cwmp)# request outstanding 6 (Optional) Sets the count for the number of requests that can be sent by CPE to ACS without receiving the acknowledgement. The range for the request count argument is 0 to 10. The default value is 5. Step 16 parameter change notify interval time-interval Example:Device(config-cwmp)# parameter change notify interval 75 (Optional) Sets the time interval, in seconds, for the parameter change notifications. The range for the time interval argument is 15 to 300. The default value is 60. Step 17end Example:Device(config-cwmp)# end Exits TR-069 Agent configuration mode and returns to privileged EXEC mode. What to Do NextProceed to Enabling the TR-069 Agent on the CPE task. Enabling the TR-069 Agent on the CPEBefore You BeginYou must have set up the CPE as specified in the Setting Up the CPE to Communicate with the ACS task. SUMMARY STEPS1. enable 2. configure terminal 3. cwmp agent 4. enable 5. end DETAILED STEPS Command or ActionPurposeStep 1 enable Example:Device> enable Enables privileged EXEC mode. Enter your password if prompted. Step 2 configure terminal Example:Device# configure terminal Enters global configuration mode. Step 3 cwmp agent Example:Device(config)# cwmp agent Enables TR-069 Agent configuration mode. Step 4 enable Example:Device(config-cwmp)# enable Enables the CPE to initiate a TR-069 session with the ACS. Step 5end Example:Device(config-cwmp)# end Exits TR-069 Agent configuration mode and returns to privileged EXEC mode. Initiating a TR-069 Agent Session from the ACSBefore You BeginYou must have set up the CPE by using Setting Up the CPE to Communicate with the ACS task and enabled the TR-069 Agent on the CPE by using the Enabling the TR-069 Agent on the CPE task. SUMMARY STEPS1. enable 2. configure terminal 3. cwmp agent 4. connection request username username 5. connection request username [ encryption-type | cleartext-password ] passwd 6. end DETAILED STEPS Command or ActionPurposeStep 1 enable Example:Device> enable Enables privileged EXEC mode. Enter your password if prompted. Step 2 configure terminal

The value in Cisco ISR G2; only one storage path and it is the flash memory. ntp server 100.12.12.1 YES (no archive) YES (configure archive) Prerequisites for the TR-069 Agent The CPE should have an IP address and a WAN connection should be established to access the ACS. Information About the TR-069 AgentTR-069 AgentHTTP Digest Authentication SupportHTTP Cookie Support Per RFC2965Device Gateway Association and Port Mapping SupportTR-069 Agent The TR-069 Agent allows an ACS to provision a CPE or collection of CPEs. The provisioning mechanism includes specific provisioning parameters and a general mechanism for adding vendor-specific provisioning capabilities as needed. The identification mechanisms included in the protocol allow CPE provisioning based either on the requirements of each specific CPE, or on collective criteria such as the CPE vendor, model, software version, or other criteria. The provisioning mechanism allows CPE provisioning at the time of initial connection to the broadband access network and the ability to reprovision at any subsequent time. This includes support for asynchronous ACS-initiated reprovisioning of a CPE. The TR-069 Agent also supports image upgrade, configuration application, file downloads, configuration and log file uploads, and CPE monitoring. Note The TR-069 Agent CPE devices must be set up and enabled for TR-069. An ACS used to communicate with the CPE must be TR-069 compliant in order to enable the TR-069 Agent. RPC Support The following remote procedure calls (RPCs) supported with the TR-069 Agent: Standard RPCs GetRPCMethods SetParameterValues GetParameterValues GetParameterNames SetParameterAttributes GetParameterAttributes AddObject DeleteObject Reboot Download Upload Vendor RPCs X_00000C_SetConfiguration X_00000C_ShowStatus CWMP Vendor Profile Schema The following details the CWMP vendor profile schema: For SetConfiguration, rollback {running-config | startup-config} block of clis separated by newline [\n] character IOS Configuration command 1 IOS Configuration command 2 parameterkey ErrorOption => string with length 64Target => string with length 64 On success, 0 On failure, ClientCWMP fault IOS Configuration command that failedparse_cmd() return value IOS Configuration command that failedparse_cmd() return value For ShowStatus, IOS Exec command 1 IOS Exec command 2 IOS Exec command 3 On success, IOS Exec command 1 output of command 1 IOS Exec command 2 output of command 2 IOS Exec command 3 output of command 3 On failure, ClientCWMP fault HTTP Digest Authentication Support The TR-069 Agent uses HTTP as the transport and needs support for digest authentication from the HTTP client infrastructure. Note This feature is not a TR-069 Agent-exclusive feature and can be used in